cenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizers
cenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizerscenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizerscenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizerscenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizers

Process and Applications

Equipment
Fluid Cleaning (F) fluid cleaning
Clarifuge
225 & 236
 Removes suspended solids from liquid
 w Grinding coolants
 w Cutting oils
 w Quench oils
 w Vibratory finishing waste water
 w Lens grinding coolant
 w Deep hole drilling coolants
 w Wire drawing lubricants
Oil Extraction / Chip Wringing (E) oil / sludge extraction, chip wringing, washing / drying
Chip Wringer
301 & 601

or

oil / sludge extraction, chip wringing, washing / drying
Fluid Extractor
401, 402, 1101
& 1100
 Separates industrial fluids from solids
 w Cutting oil from metal chips and turnings
 w Water soluble coolant from chips or turnings
 w Oil or coolant from parts
 w Oil or coolant from stampings
Chip Washing (CW)
 Degrease and clean parts + Oil Extractor
 pan and cover
 Chips are washed with hot detergent to
 remove oil and dried prior to the remelt operation.
Washing / Drying (WD)
 Degrease and clean parts
 w Screw machine parts
 w Cold headed parts
 w Fasteners and fittings
Sludge Extraction(SES):
 Removes liquid from most sludge.
 w Honing Sludges
 w Glass Grinding
 w Most types of metal grinding
 w Quench oil slag
Galvanizer (GA): galvanizer
Galvanizer
 Spins molten metals (zinc or tin) from
 industrial parts and leaves uniform
 rust-resistant coating.
Custom Centrifuge (CC): cenrifuges for fluid cleaning, oil / sludge extraction, chip wringing, washing and galvanizers
Custom
Systems
 Custom systems for your specific
 application can be provided upon
 request.
Fluid Extractor Machine Capacities
Previous
Unit
Number		 New Unit
Number		 Product
Name 		Load
Weight
Capacity		 Load
Liquid
Capacity		 Max.
RPM		 Max. Gs Wringer Basket
Size
401/402   Oil Extractor 225 lbs. 16 gal. 1,200 470 23" dia. x 15" dp.
1101/1100   Oil Extractor 425 lbs. 33 gal. 900 345 30" dia. x 14" dp.
Oil Extraction / Chip Wringing Kine-Spin 11001100 with pan hoistKine-Spin 1100 with wash tank

KineSpin Fluid Extractors provide rapid acceleration and high "G"
forces to effectively and efficiently extract all recoverable fluids
in a short cycle providing maximum fluid recovery. Also
offering programmable cycles with PLC and touch screen
controls. Proven rugged design with direct motion drive to
interior components.

Oily Chips Dry Chips Extracted Oil
Sludge (Swarf) Extraction
By spinning a water-based sludge in any KineSpin Sludge
Extractor for 15-20 minutes, you will typically remove all the
free liquid and reduce the wet sludge to a dry cake. (Oil-based
sludges typically require a 30-45 minute cycle time). Because
sludge applications vary greatly, it is impossible to say with
certainty how dry your sludge would be after spinning. It is not
unusual to reduce wet sludges to a 5-15% moisture level.
Sludge (Swarf) Sludge After (Dried) Extracted Oil
Washing / Drying
Centrifugal washing and drying offers a range of benefits
including typically shorter cycles, limited floor space, high
production rate, bulk loads or part fixturing, multiple basket
designs. Introduce aqueous detergent solutions, rinse water or
water- based coating of parts. Heat options to drying cycles.
Cleaning Hollow Parts Removing Test Oil from Units Coating Glass Plates

Literature:
402-E & 1100-E Fluid Extractors
402 & 1100 Washer / Dryer
301 Spintech Chip Wringer
601 Versa-Fuge System
Contact us to learn more

KINESPIN Division, Kinefac® Corporation
Phone: (508) 754-6891 . Email us at: kinespin@kinefac.com 
For more information on Kinefac Corporation of quality products and services, please visit us at: www.kinefac.com
Copyright © 2019 Kinefac Corporation